Step four in the recording studio design process

Step four has arrived: you’ve worked out what you want, you budget and timeline, and given some thought to how you will use the studio, and how you will get it built. in this post, we’ll look at how to capture the relevant space in both a simple hand sketch, and then using a tool (like Google SketchUp – a free version is available @ to model your existing space. this sets the stage for then laying out your space and ideally having some folks comment on it (John Sayers’ Studio Building Forum ( is hands down the best resource for this).

For our discussion we’ll assume you have a spare room in your house which you want to convert into a control room where you could also record some acoustic instruments but most of your work is done electronically into a digital audio workstation via some analog-to-digital converter boxes/mixers etc.  we’ll assume that you do not plan on very loud mixing sessions (since you like your ears and only turn it up to do final tweaks), and your room is on the first floor over an unfinished basement (which for some reason you cannot use…) and is bounded by the outside wall, living room, and another room. your neighbors are about 30ft (10m) away and your ambient noise levels outdoors consist of some car traffic and little or no air traffic can be heard. since it is a project studio and not a commercial studio, and you cannot re-structure the house, you’ll make best efforts to add some isolation and keep your loud work for daytime hours when it is acceptable. otherwise you are really looking for good acoustics for mixing and the infrequent acoustic guitar or horn instrument.

You set up your monitoring equipment and a recording which you played at 100db (based on your sound meter) (which is what you think is as loud as you intend to get) and went outside to measure how much isolation you need. except for the near (1m) window where you were reading about 85db, the overall sound level by the neighbor’s house is about 50db so you know the window needs to get some attention but overall not too bad. inside the house, the living room and other room by the closet were reading about 70db so you know you need some work. in the basement is was around 70db but it is all storage and the leakage out the basement windows is lower than the room window but you might consider some isolation under the floor since once you fix the room window the basement will be the main source of leakage.

the following figure is what you drew on some graph paper.

you are not too concerned with getting it scaled to match the grid lines on the paper as much as keep it neat and making sure all the measurements are accurate and all the important room retails are included. in looking at the drawing we see a few things might be missing (some measurements and a light switch for the closet) but in general it has most of the information we need to start modeling the room. one thing is immediately apparent: the HVAC uses a supply into the room and the return is located in the hallway and the airflow is under the door. to seal the door and reduce the sound into the hallway, you may consider adding a return into the room or possible venting outside.

the next step is to create a model in SketchUp (SU) or other tool (AutoCAD, etc) so you can readily visualize the design and it makes working with people online much easier. in general, start with the biggest details and work down. this means draw a box which are the main room dimensions. then add the smaller closet box and remember to factor in the partition wall when creating its depth. now you have two boxes. using the offset tool (in SU) you can expand the room to factor in the drywall, framing depth, etc. once you trim and adjust the lines to reflect a good 2D view of the room from the top, you should save that as your first template. this way if you need to re-start from that point, you can simply open up a new file based on it and re-work it.

then you can add the framing, drywall, electric components, doors, etc. until your room looks like, er, your room! if this is too much detail for you, consider just working off the 2D floor plan. the following figure shows a good 3D view of the room including the relevant bits like outlets, light fixtures, and HVAC  registers are so you can do your design around them or know what you need to move.

next post we’ll start to put in some design ideas for isolation and ventilation so we can prepare for the acoustic treatments. meanwhile, get measuring! start playing with SketchUp, and start visiting and learning on the recording studio design forums!

2 thoughts on “Step four in the recording studio design process

  1. Pingback: Step four in the recording studio design process « Gullfo's … |

Leave a Reply

Please log in using one of these methods to post your comment: Logo

You are commenting using your account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s